- 您现在的位置：买卖IC网 > Sheet目录337 > LT3599IFE#PBF (Linear Technology)IC LED DRVR WHITE BCKLGT 28TSSOP
LT3599
APPLICATIONS INFORMATION
( I SS = 11μA typ )
Δ V SS I
= SS
asoft-startlatchissetcausingtheSSpintobedischarged
(see the Soft-Start Pin Timing Diagram in Figure 11). All
faults are detected internally and do not require external
components. When all faults no longer exist and the SS
pin has been discharged to at least 0.25V, the soft-start
latch is reset and an internal 11μA supply charges the SS
pin. During start-up or recovery from a fault, the SS pin
ramp up controls the ramp up of switch current limit.
Soft-start ramp rate is given by:
Δ T C SS
A 10nF capacitor from the SS pin to ground will therefore
provide a 1V/ms ramp rate on the SS pin.
In addition, during soft-start, switching frequency is
reduced to protect the inductor from high currents.
SW
cause very slow start-up of LED displays for applications
using very high PWM dimming ratios.
OPENLED FLAG
The OPENLED pin is an open-collector output and needs
an external resistor tied to a supply (see Figure 12). If any
LED string is open during normal operation, the OPENLED
pin will be pulled down.
The open LED detection is enabled only when the PWM
signal is enabled. There is a delay for OPENLED ?ag
generation when the PWM signal is enabled to avoid
generating a spurious ?ag signal.
During start-up (see the Operation section), the open LED
detection is disabled.
SHORTLED FLAG
The SHORTLED pin is an open-collector output, and needs
an external resistor tied to a supply (see Figure 12). If any
SS
FAULTS TRIGGERING
SOFT-START LATCH
WITH SW TURNED OFF
IMMEDIATELY:
V IN < 2.7V
OR
SHDN < 1.4V
SOFT-START
LATCH SET
0.3V (ACTIVE THRESHOLD)
0.25V (RESET THRESHOLD)
0.15V
SOFT-START
LATCH RESET:
SS < 0.25V
AND
V IN > 2.7V
AND
SHDN > 1.4V
AND
PWM > 1V (FOR >200ns)
3599 F12
LED pin is shorted to V OUT during normal operation, the
SHORTLED pin will be pulled down. In addition, the shorted
LED string (channel) is immediately disabled, thereby
protecting the LT3599. During the short circuit fault, cable
inductance can cause the LED pin voltage to overshoot
past V OUT voltage. To avoid LED pin voltage exceeding it’s
absolute maximum rated voltage, the anode of a 1N4148WS
diode should be connected to the LED pin and the cathode
of the diode connected to the V OUT pin.Keep the traces as
short as possible. A Schottky diode should not be used
Figure 11. Soft-Start Pin Timing Diagram
A useful feature of the LT3599 is that it waits for the ?rst
PWM pin active high (minimum 200ns pulse width) before
it allows the soft-start of V C pin to begin. This feature
ensures that during start-up of the LT3599 the soft-start
ramp has not timed out before PWM is asserted high.
Without this ‘wait for PWM high’ feature, systems which
apply PWM after V IN and SHDN are valid, can potentially
due to high reverse bias leakage currents.
The short LED detection is enabled only when the PWM signal
is enabled. There is a delay for SHORTLED ?ag generation
when the PWM signal is enabled to avoid spurious signal
being generated.
During start-up, the SHORTLED ?ag is disabled (see the
Operation section).
LT3599
turn on without soft-start and experience high inductor
R1
R2
currents during wake up of the converter’s output voltage.
It is important to note that when PWM subsequently goes
low, the soft-start ramp is not held at its present voltage
but continues to ramp upwards. If the soft-start ramp
voltage was held every time PWM goes low, this would
OPENLED
SHORTLED
3599 F13
Figure 12. OPENLED and SHORTLED Connection
3599fe
16
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LT3743EFE#PBF
IC LED DVR HP CONST CURR 28TSSOP
LT3745IUJ#TRPBF
IC LED DVR 16CH 50MA 40QFN
LT3746IUHH#TRPBF
IC LED DRIVER 32CHANNEL 56-QFN
LT3754IUH#TRPBF
IC LED DVR 16CH 50MA 32QFN
LT3755EMSE#PBF
IC LED DRVR HP CONS CURR 16-MSOP
LT3760EFE#PBF
IC LED DVR WHT/CLR BCKLT 28TSSOP
LT3799IMSE#PBF
IC LED DRIVER TRIAC DIM 16-MSOP
LT3956EUHE#PBF
IC LED DVR BUCK BOOST 36-VQFN
相关代理商/技术参数
LT3599IFE#TRPBF
功能描述:IC LED DRVR WHITE BCKLGT 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND
LT3599IFEPBF
制造商:Linear Technology 功能描述:LED Driver 40-Seg 3.3/5/9/../24V TSSOP28
LT3599IFE-PBF
制造商:LINER 制造商全称:Linear Technology 功能描述:4-Channel 120mA LED Driver with ±1.5% Current Matching
LT3599IFETRPBF
制造商:LINER 制造商全称:Linear Technology 功能描述:4-Channel 120mA LED Driver with ±1.5% Current Matching
LT3599IFE-TRPBF
制造商:LINER 制造商全称:Linear Technology 功能描述:4-Channel 120mA LED Driver with ±1.5% Current Matching
LT3599IUH
制造商:LINER 制造商全称:Linear Technology 功能描述:4-Channel 120mA LED Driver with ±1.5% Current Matching
LT3599IUH#PBF
功能描述:IC LED DRIVR WHITE BCKLGT 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C
LT3599IUH#PBF
制造商:Linear Technology 功能描述:LED DRIVER BOOST PWM 2.06MH 制造商:Linear Technology 功能描述:LED DRIVER, BOOST, PWM, 2.06MHZ, QFN-32